Javascript required
Skip to content Skip to sidebar Skip to footer

How to Set a Compass to True North

Example of magnetic declination showing a compass needle with a "positive" (or "easterly") variation from geographic north. Ng is geographic or true north, Nm is magnetic north, and δ is magnetic declination

Magnetic declination, or magnetic variation, is the angle on the horizontal plane between magnetic north (the direction the north end of a magnetized compass needle points, corresponding to the direction of the Earth's magnetic field lines) and true north (the direction along a meridian towards the geographic North Pole). This angle varies depending on position on the Earth's surface and changes over time.

Somewhat more formally, Bowditch defines variation as "the angle between the magnetic and geographic meridians at any place, expressed in degrees and minutes east or west to indicate the direction of magnetic north from true north. The angle between magnetic and grid meridians is called grid magnetic angle, grid variation, or grivation."[1]

By convention, declination is positive when magnetic north is east of true north, and negative when it is to the west. Isogonic lines are lines on the Earth's surface along which the declination has the same constant value, and lines along which the declination is zero are called agonic lines. The lowercase Greek letter δ (delta) is frequently used as the symbol for magnetic declination.

The term magnetic deviation is sometimes used loosely to mean the same as magnetic declination, but more correctly it refers to the error in a compass reading induced by nearby metallic objects, such as iron on board a ship or aircraft.

Magnetic declination should not be confused with magnetic inclination, also known as magnetic dip, which is the angle that the Earth's magnetic field lines make with the downward side of the horizontal plane.

Declination change over time and location [edit]

Magnetic declination varies both from place to place and with the passage of time. As a traveller cruises the east coast of the United States, for example, the declination varies from 16 degrees west in Maine, to 6 in Florida, to 0 degrees in Louisiana, to 4 degrees east in Texas. The declination at London, UK was one degree west (2014), reducing to zero as of early 2020.[2] [3] Reports of measured magnetic declination for distant locations became commonplace in the 17th century, and Edmund Halley made a map of declination for the Atlantic Ocean in 1700.[4]

In most areas, the spatial variation reflects the irregularities of the flows deep in the Earth; in some areas, deposits of iron ore or magnetite in the Earth's crust may contribute strongly to the declination. Similarly, secular changes to these flows result in slow changes to the field strength and direction at the same point on the Earth.

Level curves drawn on a declination map to denote the magnetic declination, described by signed degrees. Each level curve is an isogonic line.

NIMA Magnetic Variation Map 2000

The magnetic declination in a given area may (most likely will) change slowly over time, possibly as little as 2–2.5 degrees every hundred years or so, depending upon how far from the magnetic poles it is. For a location closer to the pole like Ivujivik, the declination may change by 1 degree every three years. This may be insignificant to most travellers, but can be important if using magnetic bearings from old charts or metes (directions) in old deeds for locating places with any precision.

As an example of how variation changes over time, see the two charts of the same area (western end of Long Island Sound), below, surveyed 124 years apart. The 1884 chart shows a variation of 8 degrees, 20 minutes West. The 2008 chart shows 13 degrees, 15 minutes West.

Western Long Island Sound, 1884

Western Long Island Sound, 2008

Estimated declination contours by year, 1590 to 1990

Determining declination [edit]

Magnetic declination indicated on an Israeli map. The arrows show true north, grid north and magnetic north, and the caption explains that the average yearly change in the magnetic declination is 0°03′ eastward.

Direct measurement [edit]

The magnetic declination at any particular place can be measured directly by reference to the celestial poles—the points in the heavens around which the stars appear to revolve, which mark the direction of true north and true south. The instrument used to perform this measurement is known as a declinometer.

The approximate position of the north celestial pole is indicated by Polaris (the North Star). In the northern hemisphere, declination can therefore be approximately determined as the difference between the magnetic bearing and a visual bearing on Polaris. Polaris currently traces a circle 0.73° in radius around the north celestial pole, so this technique is accurate to within a degree. At high latitudes a plumb-bob is helpful to sight Polaris against a reference object close to the horizon, from which its bearing can be taken.[5]

Determination from maps and models [edit]

A rough estimate of the local declination (within a few degrees) can be determined from a general isogonic chart of the world or a continent, such as those illustrated above. Isogonic lines are also shown on aeronautical and nautical charts.

Larger-scale local maps may indicate current local declination, often with the aid of a schematic diagram. Unless the area depicted is very small, declination may vary measurably over the extent of the map, so the data may be referred to a specific location on the map. The current rate and direction of change may also be shown, for example in arcminutes per year. The same diagram may show the angle of grid north (the direction of the map's north–south grid lines), which may differ from true north.

On the topographic maps of the U.S. Geological Survey (USGS), for example, a diagram shows the relationship between magnetic north in the area concerned (with an arrow marked "MN") and true north (a vertical line with a five-pointed star at its top), with a label near the angle between the MN arrow and the vertical line, stating the size of the declination and of that angle, in degrees, mils, or both.

A prediction of the current magnetic declination for a given location (based on a worldwide empirical model of the deep flows described above) can be obtained online from a web page operated by the National Geophysical Data Center, a division of the National Oceanic and Atmospheric Administration of the United States.[6] This model is built with all the information available to the map-makers at the start of the five-year period it is prepared for. It reflects a highly predictable rate of change,[ clarification needed ] and is usually more accurate than a map—which is likely months or years out of date—and almost never less accurate.[ citation needed ]

Software [edit]

The National Geospatial-Intelligence Agency (NGA) provides source code written in C that is based on the World Magnetic Model (WMM). The source code is free to download and includes a data file updated every five years to account for movement of the magnetic north pole.

Using the declination [edit]

Adjustable compasses [edit]

Adjustable compass set to a declination of 0° and a bearing of 312°

A magnetic compass points to magnetic north, not geographic north. Compasses of the style commonly used for hiking include a declination adjustment in the form of a bezel which swivels relative to the base plate. To establish a declination the bezel is rotated until the desired number of degrees plus or minus lie between the bezel's designation N (for North) and the direction indicated by the magnetic end of the needle (usually painted red). This allows the user to establish a true bearing for travel or orientation by aligning the embossed red indicator arrow on the base plate with a landmark or heading on a map. A compass thus adjusted can be said to be reading "true north" instead of magnetic north (as long as it remains within an area on the same isogonic line).

In the image to the left, the bezel's N has been aligned with the direction indicated by the magnetic end of the compass needle, reflecting a magnetic declination of 0 degrees. The arrow on the base plate indicates a bearing of 312 degrees.

Non-adjustable compasses [edit]

How to compensate for magnetic declination when reading a compass. In this example, the declination is 14°E (+14°), so the compass card points to a "north" 14 degrees to the East of true North. To obtain a true bearing, add 14 degrees to the bearing shown by the compass.

To work with both true and magnetic bearings, the user of a non-adjustable compass needs to make simple calculations that take into account the local magnetic declination. The example on the left shows how you would convert a magnetic bearing (one taken in the field using a non-adjustable compass) to a true bearing (one that you could plot on a map) by adding the magnetic declination. The declination in the example is 14°E (+14°). If, instead, the declination was 14°W (−14°), you would still "add" it to the magnetic bearing to obtain the true bearing: 40°+ (−14°) = 26°.

The opposite procedure is used in converting a true bearing to a magnetic bearing. With a local declination of 14°E, a true bearing (perhaps taken from a map) of 54° is converted to a magnetic bearing (for use in the field) by subtracting the declination: 54° – 14° = 40°. If, instead, the declination was 14°W (−14°), you would still "subtract" it from the true bearing to obtain the magnetic bearing: 54°- (−14°) = 68°.

Navigation [edit]

On aircraft or vessels there are three types of bearing: true, magnetic, and compass bearing. Compass error is divided into two parts, namely magnetic variation and magnetic deviation, the latter originating from magnetic properties of the vessel or aircraft. Variation and deviation are signed quantities. As discussed above, positive (easterly) variation indicates that magnetic north is east of geographic north. Likewise, positive (easterly) deviation indicates that the compass needle is east of magnetic north.[7]

Compass, magnetic and true bearings are related by:

T = M + V {\displaystyle T=M+V}

M = C + D {\displaystyle M=C+D}

The general equation relating compass and true bearings is

T = C + D + V {\displaystyle T=C+D+V}

Where:

For example, if the compass reads 32°, the local magnetic variation is −5.5° (i.e. West) and the deviation is 0.5° (i.e. East), the true bearing will be:

T = 32 + ( 5.5 ) + 0.5 = 27 {\displaystyle T=32^{\circ }+(-5.5^{\circ })+0.5^{\circ }=27^{\circ }}

To calculate true bearing from compass bearing (and known deviation and variation):

  • Compass bearing + deviation = magnetic bearing
  • Magnetic bearing + variation = true bearing

To calculate compass bearing from true bearing (and known deviation and variation):

  • True bearing - variation = Magnetic bearing
  • Magnetic bearing - deviation = Compass bearing

These rules are often combined with the mnemonic "West is best, East is least"; that is to say, add W declinations when going from True bearings to Magnetic bearings, and subtract E ones.

Another simple way to remember which way to apply the correction for continental USA is:

  • For locations east of the agonic line (zero declination), roughly east of the Mississippi: the magnetic bearing is always bigger.
  • For locations west of the agonic line (zero declination), roughly west of the Mississippi: the magnetic bearing is always smaller.

Common abbreviations are:

  • TC = true course;
  • V = variation (of the Earth's magnetic field);
  • MC = magnetic course (what the course would be in the absence of local deviation);
  • D = deviation caused by magnetic material (mostly iron and steel) on the vessel;
  • CC = compass course.

Deviation [edit]

Magnetic deviation is the angle from a given magnetic bearing to the related bearing mark of the compass. Deviation is positive if a compass bearing mark (e.g., compass north) is right of the related magnetic bearing (e.g., magnetic north) and vice versa. For example, if the boat is aligned to magnetic north and the compass' north mark points 3° more east, deviation is +3°. Deviation varies for every compass in the same location and depends on such factors as the magnetic field of the vessel, wristwatches, etc. The value also varies depending on the orientation of the boat. Magnets and/or iron masses can correct for deviation, so that a particular compass accurately displays magnetic bearings. More commonly, however, a correction card lists errors for the compass, which can then be compensated for arithmetically. Deviation must be added to compass bearing to obtain magnetic bearing.

Air navigation [edit]

Aviation sectional charts (maps) and databases used for air navigation are based on true north and south because the planetary rotational poles do not change location on the landscape anywhere near as much as do the magnetic poles. That said, low-tech ways of identifying true north or south include waiting for noon with a stick in the ground to judge the shortest shadow, or waiting for a clear night in order to consult a pole star. By contrast, with a low-tech magnetic compass, one can identify magnetic north or south at any time, hence the presence of a magnetic compass in every cockpit, even today in the GPS era. When onboard electronics fail, pilots can still rely on paper charts and Edwardian-era instruments such as a magnetic compass. There is still the need to convert magnetic to true, however. Sectional charts indicate by dashed magenta lines the number of degrees variation between true and magnetic at any local vicinity as of the printing of that chart. Since the true locations of the magnetic poles meander over time, occasionally quite dramatically, charts and databases are required to be updated at least twice each year. Another reason for frequent chart updates is construction (new tall radio towers, runway renovation, etc.).

For example, as of March 2021, slightly west of Winston-Salem, North Carolina, magnetic north is 8 degrees west of true north (Note the dashed line marked 8°W).[8]

When plotting a course, some small aircraft pilots plot a trip using true north on a sectional chart (map), then convert the true north bearings to magnetic north for in-plane navigation using the magnetic compass. These bearings are then converted on a pre-flight plan by adding or subtracting the local variation displayed on a sectional chart.

Radionavigation aids located on the ground, such as VORs, are also checked and updated to keep them aligned with magnetic north to allow pilots to use their magnetic compasses for accurate and reliable in-plane navigation.

Runways are designated by a number between 01 and 36, which is generally one tenth of the magnetic azimuth of the runway's heading: a runway numbered 09 points east (90°), runway 18 is south (180°), runway 27 points west (270°) and runway 36 points to the north (360° rather than 0°).[9] However, due to magnetic declination, changes in runway designators have to occur at times to keep their designation in line with the runway's magnetic heading. An exception is made for runways within the Northern Domestic Airspace of Canada; these are numbered relative to true north because proximity to the magnetic North Pole makes the magnetic declination large and changes in it happen at a high pace.

GPS systems used for air navigation can use magnetic north or true north. In order to make them more compatible with systems that depend on magnetic north, magnetic north is often chosen, at the pilot's preference. The GPS receiver natively reads in true north, but can elegantly calculate magnetic north based on its true position and data tables; the unit can then calculate the current location and direction of the north magnetic pole and (potentially) any local variations, if the GPS is set to use magnetic compass readings.

References [edit]

  1. ^ Bowditch, Nathaniel (2002). American Practical Navigator. Paradise Cay Publications. p. 849. ISBN9780939837540.
  2. ^ "Find the magnetic declination at your location". Magnetic-Declination.com. Retrieved 6 December 2013.
  3. ^ "World Magnetic Model - Epoch 2020 -Declination" (PDF).
  4. ^ Government of Canada, Natural Resources Canada. "Magnetic declination". www.geomag.nrcan.gc.ca . Retrieved 2021-09-30 .
  5. ^ Magnetic declination, what it is , how to compensate., archived from the original on 2010-01-07, retrieved 2010-03-03
  6. ^ "Estimated Value of Magnetic Declination". Geomagnetism. NOAA National Geophysical Data Center. Retrieved 6 December 2013.
  7. ^ Willemsen, Diederik. "Compass navigation". SailingIssues . Retrieved 4 January 2020.
  8. ^ See also CUNY
  9. ^ Federal Aviation Administration Aeronautical Information Manual, Chapter 2, Section 3 Airport Marking Aids and Signs part 3b Archived 2012-01-18 at the Wayback Machine

External links [edit]

  • USGS Geomagnetism Program
  • Looks up your IP address location and tells you your declination.
  • Online declination calculator at the National Geophysical Data Center (NGDC)
  • Online declination and field strength calculator at the NGDC
  • Mobile web-app for magnetic declination at the NGDC
  • Historical magnetic declination viewer at the NGDC
  • Magnetic declination calculator at Natural Resources Canada
  • A Google spreadsheet application to bulk calculate magnetic declination
  • World Magnetic Model source code download site

How to Set a Compass to True North

Source: https://en.wikipedia.org/wiki/Magnetic_declination